AUTONET TV

Not Too Hot and Not Too Cold (Temperature Gauge)

You know your body temperature is supposed to be 98.6 degrees F, 37 degrees C.  Your vehicle has a normal temperature, too, and if you pay attention to it, that can save you some big headaches down the road.

Many vehicles have a temperature gauge on the dash that takes the temperature of the engine's coolant.  Some have a thermometer symbol, some read C-H (cold to hot). Many will have a red zone that shows when water temperature is getting into the danger zone.  Others are digital and have a red warning light that signals overheating.  And some vehicles have a light that goes on when the engine temperature is out of the normal range.

If your vehicle has a gauge, pay attention to it.  If you need help locating it, ask one of our A.G. Automotive & Diagnosis experts to give you a quick explanation.  Chances are when the vehicle has been running for 15 minutes or more, the temperature gauge will settle into its own "normal" zone, often just below the midway point.  If you have a digital readout, remember what that "normal" temperature is.  Here's why.

At any point when you're driving, the temperature gauge is the quickest way to get a sense that the engine is running the way it should, a quick health checkup, as it were. Say you're on a 3-hour trip, glance at that gauge every hour or so.  It should always be in the same spot.  If it starts to move one way or the other, you may be able to catch a problem before it gets serious.

Pay special attention to it moving into the hot zone.  The needle on the gauge is the easiest and least distracting way to see an engine heating up, but on a digital gauge, start paying attention if the temperature reaches 240ºF/115ºC or more.

Remember, though, that just because the gauge reads "hot" doesn't mean your engine is on the verge of burning up.  It could be a bad sensor and the engine will be at a normal temperature.  But it also could be a failing water pump, coolant leak or thermostat.  By pulling off the road and observing your engine, it will give you a pretty good idea if it's running hot or not.

If the gauge is too "cold," it could be a broken gauge or thermostat sticking open.  Usually being in the cold range isn't as worrisome, but you should have it checked out since other systems may be affected.

Heat is one of a vehicle's worst enemies, especially when it comes from within.  Know your vehicle's normal temperature and keep an eye on it.

A.G. Automotive & Diagnosis
19735 Sherman Way Suite 2
Winnetka, CA 91306
(818) 438-9608
http://www.agautodiagnosis.com

Let's Clear Some Things Up (Headlight Restoration)

You know how exposing your skin to sunlight can cause sunburn and other unhealthy things.  Sunlight can also create major problems for your headlights.  After they've been exposed to ultraviolet light, acrylic headlights can yellow and fog due to oxidation.  And when that happens, less light can pass through the plastic, reducing the effectiveness—and safety—of your headlights. 

It's not just the UV light that causes headlights to turn cloudy.  Road grime and debris gets kicked up and can scratch the plastic, diffusing the light that should pass through them when they're clear.  Plus, when your vehicle was new from the factory, the headlights had watertight seals all around to prevent moisture from getting into them and fogging them up with water vapor.  Just like clouds can hide the sun, tiny water molecules can diffuse the light from your headlight bulbs. 

Sure, you could buy replacement parts and start fresh.  But the good news is many vehicle repair facilities can restore your original headlights to perform like they did when you first bought your vehicle.  Here's how it works:

• A technician will protect your vehicle's paint by either taking the headlights out or by taping off the paint near the headlights and leaving them in place.
• Residue is removed from the headlight surfaces by wet sanding to remove the oxidized plastic.
• Using special compounds, the technician will buff and polish the surface of the lens so it looks as smooth as glass. 
• The newly-polished plastic is then sealed with wax or a special sealant designed to keep them operating like new. 
• If the seals that keep the moisture out of the inside of your headlights have dried out or cracked, they will be restored or replaced to keep condensation from forming again.

Visibility at night is vital for safe driving, and if your headlights aren't performing up to their potential, the less you'll be able to see ahead of you.

There are many advantages of having your headlights restored rather than buying new or aftermarket replacements.  It's friendlier to the planet since plastics are made of oil, so it's reducing the amount of plastic that is manufactured.  And it's usually cheaper to have your headlights restored rather than replaced.

Consider headlight restoration a way to literally recycle those parts of your vehicle.  That seems to be perfectly clear!

A.G. Automotive & Diagnosis
19735 Sherman Way Suite 2
Winnetka, CA 91306
(818) 438-9608
http://www.agautodiagnosis.com

Them's the Brakes (Brake Rotor Resurfacing)

Your vehicle's brakes wear out.  It's inevitable. You'll notice it when you step on the brake pedal and feel it harder to stop, or there's vibration when you are braking. 

Most modern vehicles have disc brakes that each use a brake pad that press on a disc (disc brakes!) called a rotor.  The friction between them enables you to stop, and each time you do a little bit of the pad and the rotor wears down.

The original brakes on vehicles used a rotor that was thick enough to last through at least two replacements of the pads.  But vehicle manufacturers who want to save costs and weight now make them thinner, and sometimes the rotors have to be replaced after the first pad replacement.  But not always.

Vehicle manufacturers specify a minimum thickness to provide safe braking.  Sometimes rather than having to have your rotors replaced, they can be put on a lathe and resurfaced.  In other words, the surfaces of the disc can be slightly shaved off so the surface is flat and doesn't wobble. 

Whenever you bring your vehicle in to have the brakes checked, the technician will measure the thickness of the rotors to see if they can be resurfaced without leaving them too thin for safe braking. If they can, with the right tools and skill, the rotors can be resurfaced.  If not, the rotors should be replaced. 

Discuss the options with your service advisor.  Our service center can recommend replacements that are designed to help stop your vehicle as well as or better than the vehicle's original rotors.

Either way, keep in mind that keeping your brakes in top condition can supply the margin of safety that may one day save your life or the lives of those around you.

A.G. Automotive & Diagnosis
19735 Sherman Way Suite 2
Winnetka, CA 91306
(818) 438-9608
http://www.agautodiagnosis.com